For the time being i don't need an 060 and i'll just try boosting the 040 and if i decide to upgrade to an 060 the new crystal i'll be putting in will mean that i can run the 060 at 66.67 mhz for a small turbo boost if i ever decide to get one.
My location
For the time being i don't need an 060 and i'll just try boosting the 040 and if i decide to upgrade to an 060 the new crystal i'll be putting in will mean that i can run the 060 at 66.67 mhz for a small turbo boost if i ever decide to get one.
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD
@Buleste
sounds like a plan m8y.
the 040@40 will push about 35Mips, where as an 060@50,hz will push closer to 80Mips.
if you get a latent revision mask of the MC68060 these will clock to 100MHz... thats.... thats a shit load of Mips.
one of the problems you may / are likely to encounter with over clocking the 040, is the memory access speed, you will need to change / make sure that you are using the good 60ns or better memory. you may need to add another clock / oscilator for independent memory speed.
If i had a hammer, I would hammer in the morning, i would hammer in the evening, i would hammer all day
My location
I'll be following all the instructions from here so i should be allright so long as my soldering hand stays steady and true.
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD
My location
I've just been reading more on the overclocking of the PPC and my board is a 210 as it has a 60 Mhz crystal running at 3.5x not the standard 66.67Mhz running at 3.0x yet it's never been overclocked. How strange. Still thats Phase 5/DCE for you. Never let a standard get in the way of a build.
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD
My location
Just replaced the crystal for my 040 it's gone from 18.95 Mips to 25 Mips and running smoothly. Now I've done that i'll look into Overclocking my PPC. Shame I can't get a 40 Mhz crystal though.
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD
My location
It's Alive!!!!!! Today i completed the upgrade by adding a 66.667 Mhz crystal to my PPC so that it now runs at 233 Mhz and everything works fine. The best thing is as i've installed them via 8-DIN sockets should i ever find a 80Mhz crystal i'll be able to up the speed again or if things start getting a little toasty i can downgrade until i get a new heatsink and fan for the PPC. Shiny!!
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD
My location
AmigaKit have an 80 Mhz crystal in stock. That'll boost my PPC to 280Mhz which is about as fast as a 603 can go and as I'm using the sockets it's easy to install a new crystal. In the words of a Mister F. Mercury and a Mister B. Blessed "Who wants to live forever?"
A1200 Power Tower
OS 3.9 / CGX4 / OS4.0
Blizzard 210Mhz (overclocked to 266Mhz) 603e PPC with 25Mhz 040 (Overclocked to 33Mhz) 256Mb RAM
ZIV
CV64/3D
3.2Gb HDD + 20GB HDD